S11六面鉆加工中心
根據產量及工藝可選加工模式，前進后出模式，板件加工完畢即可加工下長張板，整個過程中流暢，待機時間短。前進后出方式可以連線生產，前進前出模式，主要針對單人操作或者加工量不大的情況。
銑型，層孔，引孔，通孔，雙面開槽，通槽
系統通過掃碼識別加工信息，智能高效。
計算機操作，CAD畫圖，CAM導入，可直接導入DXF,MPR,XML 等開放數據格式，操作便捷。
采用雙抓手導軌，抓料最大速度可達145M/MIN，智能檢測孔位信息有效避開開孔位置，減少鉆孔過程中換手時間。
配置氣浮工作臺和氣浮壓板，加工過程中板件上下表面形成氣層，提高板件輸送效率，同時避免劃傷板料，壓板鉆孔同時完成，保證鉆孔精度及效率，氣排鉆包安裝位置獨特，避免鉆孔時板材浮動導致孔位爆邊，偏差，并有效防止鉆包積塵導致鉆頭卡死影響生產。
根據產量及工藝可選加工模式，前進后出模式，板件加工完畢即可加工下長張板，整個過程中流暢，待機時間短。前進后出方式可以連線生產，前進前出模式，主要針對單人操作或者加工量不大的情況。
吸塵效果更佳，工件除塵效果達80%。上鉆吸塵口有兩個，下鉆吸塵口有一個
S11六面鉆加工中心
S11 six-sided machining center
銑型，層孔，引孔，通孔，雙面開槽，通槽
系統通過掃碼識別加工信息，智能高效。
計算機操作，CAD畫圖，CAM導入，可直接導入DXF,MPR,XML 等開放數據格式，操作便捷。
采用雙抓手導軌，抓料最大速度可達145M/MIN，智能檢測孔位信息有效避開開孔位置，減少鉆孔過程中換手時間。
配置氣浮工作臺和氣浮壓板，加工過程中板件上下表面形成氣層，提高板件輸送效率，同時避免劃傷板料，壓板鉆孔同時完成，保證鉆孔精度及效率，氣排鉆包安裝位置獨特，避免鉆孔時板材浮動導致孔位爆邊，偏差，并有效防止鉆包積塵導致鉆頭卡死影響生產。
根據產量及工藝可選加工模式，前進后出模式，板件加工完畢即可加工下長張板，整個過程中流暢，待機時間短。前進后出方式可以連線生產，前進前出模式，主要針對單人操作或者加工量不大的情況。
吸塵效果更佳，工件除塵效果達80%。上鉆吸塵口有兩個，下鉆吸塵口有一個
Milling, layer hole, pilot hole, through hole, double side slotting, through slot.
System is intelligent and efficient by scanning code to identify processing information.
Computer operation, CAD drawing, cam import, can directly import DXF, MPR, XML And other open data formats, easy to operate.
With double gripper guide rail, the maximum speed of material grabbing can reach 145m/min, the intelligent detection of hole position information can effectively avoid the opening position and Reduce the hand changing time in the drilling process.
Equipped with air floating table and air floating pressure plate, the upper and lower surfaces of the plate form air layer during the processing, which can improve the conveying efficiency of the plate, and avoid scratching the plate. The drilling of pressure plate is completed at the same time, which can ensure the drilling accuracy and efficiency. The installation position of air exhaust drilling package is unique, which can avoid the hole edge burst and deviation caused by the plate floating during drilling, and effectively prevent the bit stuck due to the dust accumulation in the drilling package, which can affect the production.
According to the output and process, the processing mode can be selected, and the forward and backward mode can be selected. After the plate is processed, the next long plate can be processed. The whole process is smooth and the standby time is short. The mode of forward and backward output can be online production, and the mode of forward and backward output is mainly aimed at the situation of single person operation or small amount of processing.
The dust collection effect is better, and the dust removal effect of workpiece reaches 80%. There are two suction ports in upper drilling and one suction port in lower drilling.
項目名稱Project name
加工最小板材尺寸Minimum machining plate size 30*200mm
加工最大板材尺寸Maximum machining plate size 1200*3000
XU軸（雙夾手）Xu axis (double grip)145m/min
YV軸（左右）YV axis (left and right)80m/min
ZW軸（上下鉆孔）ZW axis (drill up and down)30m/min
A軸（側靠）A axis (side)60m/min
直鉆Direct drilling上垂直鉆9 /18) 下垂直鉆6/12
Upper vertical drilling (9 / 18) and
lower vertical drilling (6 / 12)
水平鉆Horizontal drill2左+2右+2前+2后
2 left + 2 right + 2 front + 2 back
鏤銑加工電主軸Cutting and milling spindle風冷*2 Air cooled * 2
板材厚度Plate thickness9-60mm
工作氣壓Working air pressure0.6-0.8Mpa
工作電壓Working Voltage380V/50HZ